Introduction
Replacing heating element in electric dryer can be both a cost-effective solution and an easy DIY project. Mais, est-ce que ça vaut l'effort et l'investissement? Cet article approfondit les raisons d'envisager un remplacement, les coûts impliqués, et un guide étape par étape pour remplacer l'élément chauffant dans une sécheuse électrique.

Replacing Heating Element In Electric Dryer
Why Consider replacing heating element in electric dryer?
  1. Cost Efficiency: One of the primary reasons to replace a heating element is to save money. A new dryer can cost anywhere from $300 à $1000, while a new heating element typically costs between $20 et $50.
  2. Eco-friendly: Repairing appliances rather than replacing them reduces waste and is a more sustainable option.
  3. Prolonging Appliance Life: A simple replacement can significantly extend the life of your dryer, delaying the need for a major purchase.

Symptoms of a Faulty Heating Element

If you notice any of the following signs, it might be time to consider Replacing heating element in electric dryer:

  • Clothes taking longer to dry
  • No heat while drying
  • The dryer gets too hot and shuts off

Cost Analysis

Here’s a brief comparison table to weigh your options:

CostsReplacing Heating ElementBuying New Dryer
Part cost$20 – $50$300 – $1000
Labor cost (if not DIY)$50 – $100Included
Total Estimated Cost$70 – $150$300 – $1000
Environmental ImpactMinimalSignificant
Time Cost1-2 heuresDelivery Time
Appliance Lifespan IncreaseSignificantN/A
Replacing heating element in electric dryer

Step-by-Step Guide to Replacing Heating Element in Electric Dryer

Materials Needed:

  • Replacement heating element
  • Phillips screwdriver
  • Flathead screwdriver
  • Multimeter

Steps:

  1. Unplug the Dryer: Safety first! Ensure the dryer is unplugged from the power source.
  2. Access the Heating Element: Remove the back panel or the lower front access panel, depending on your dryer’s model.
  3. Locate the Heating Element: Typically situated in a metal housing near the blower.
  4. Test the Heating Element: Use a multimeter to check for continuity. If there’s no continuity, the element is faulty.
  5. Remove the Faulty Element: Detach the wires connected to the heating element,

1. Who are we?
Nous sommes basés dans le Jiangsu, Chine, à partir de 2010, vendre en Océanie(50.00%),Amérique du Nord(30.00%),Amérique du Sud(10.00%),Europe du Sud(10.00%). We have 500 ㎡ of office and 8000 ㎡of factory.

2. How can we guarantee quality?
Toujours un échantillon de pré-production avant la production en série;
Toujours inspection finale avant expédition;

3.What can you buy from us?
Cartridge Heater/Cast-In Heater/Circulation Heater/Engine Block Heater/Open Coil Heater, Finned Heater/Strip Heater/Heating Element

4. Why should you buy from us not from other suppliers?
1.Plus que 40 years experience

2.UL CE RoHS CQC ISO9001:2008

3.Le R&Équipe D

4.Fournir un rapport de test

5.Support product design

5. What services can we provide?
Conditions de livraison acceptées: GOUSSET,CFR,CIF,EXW,DDU,Livraison express;
Devise de paiement acceptée : USD, EUR,CNY;
Type de paiement accepté: T/T,L/C,D/P D/A,Money Gram,Carte de crédit,Pay Pal,Western union,Espèces,Entiercement;
Langue parlée:Anglais,Chinois,Français

A lire également

Laisser une réponse

Votre adresse email ne sera pas publiée. les champs requis sont indiqués *