Introduction
Replacing heating element in electric dryer can be both a cost-effective solution and an easy DIY project. But, is it worth the effort and investment? This article delves into the reasons for considering a replacement, the costs involved, and a step-by-step guide to replacing the heating element in an electric dryer.

Replacing Heating Element In Electric Dryer
Why Consider replacing heating element in electric dryer?
  1. Cost Efficiency: One of the primary reasons to replace a heating element is to save money. A new dryer can cost anywhere from $300 to $1000, while a new heating element typically costs between $20 och $50.
  2. Eco-friendly: Repairing appliances rather than replacing them reduces waste and is a more sustainable option.
  3. Prolonging Appliance Life: A simple replacement can significantly extend the life of your dryer, delaying the need for a major purchase.

Symptoms of a Faulty Heating Element

If you notice any of the following signs, it might be time to consider Replacing heating element in electric dryer:

  • Clothes taking longer to dry
  • No heat while drying
  • The dryer gets too hot and shuts off

Cost Analysis

Here’s a brief comparison table to weigh your options:

CostsReplacing Heating ElementBuying New Dryer
Part cost$20 – $50$300 – $1000
Labor cost (if not DIY)$50 – $100Included
Total Estimated Cost$70 – $150$300 – $1000
Environmental ImpactMinimalSignificant
Time Cost1-2 timmarDelivery Time
Appliance Lifespan IncreaseSignificantN/A
Replacing heating element in electric dryer

Step-by-Step Guide to Replacing Heating Element in Electric Dryer

Materials Needed:

  • Replacement heating element
  • Phillips screwdriver
  • Flathead screwdriver
  • Multimeter

Steps:

  1. Unplug the Dryer: Safety first! Ensure the dryer is unplugged from the power source.
  2. Access the Heating Element: Remove the back panel or the lower front access panel, depending on your dryer’s model.
  3. Locate the Heating Element: Typically situated in a metal housing near the blower.
  4. Test the Heating Element: Use a multimeter to check for continuity. If there’s no continuity, the element is faulty.
  5. Remove the Faulty Element: Detach the wires connected to the heating element,

1. Vilka är vi?
Vi är baserade i Jiangsu, Kina, börja från 2010, sälj till Oceanien(50.00%),Nordamerika(30.00%),Sydamerika(10.00%),Södra Europa(10.00%). Vi har 500 ㎡ av kontor och 8000 ㎡av fabriken.

2. Hur kan vi garantera kvalitet?
Alltid ett förproduktionsprov innan massproduktion;
Alltid slutbesiktning före leverans;

3.Vad kan du köpa av oss?
Patronvärmare/Ingjuten värmare/Cirkulationsvärmare/Motorblockvärmare/Open Coil Heater, Finnsvärmare/Stripvärmare/Värmeelement

4. Varför ska du köpa från oss inte från andra leverantörer?
1.Mer än 40 års erfarenhet

2.UL CE RoHS CQC ISO9001:2008

3.R&D-laget

4.Tillhandahålla testrapport

5.Support product design

5. Vilka tjänster kan vi tillhandahålla?
Godkända leveransvillkor: FOB,CFR,CIF,EXW,DDU,Expressleverans;
Godkänd betalningsvaluta : USD, EUR,CNY;
Godkänd betalningstyp: T/T,L/C,D/P D/A,Penga gram,Kreditkort,PayPal,Western Union,Kontanter,Escrow;
Språk som talas:engelsk,kinesiska,franska

Similar Posts

Leave a Reply

Din e-postadress kommer inte att publiceras. behövliga fält är markerade *